![]() ![]() Pressing MODE switches function, in order, as shown on the left. Measurements occur automatically when the bicycle is in use. Press the MODE when measurement has stopped and no signal is being received to change menu settings. If the MENU is pressed with the measuring screen displayed, the menu screen appears. Reset data.Ġ.0(4.0) - 105.9 km Ĭhanging the computer settings E (Error) is displayed as the average speed. *2 If Tm exceeds approximately 27 hours or DSTĮxceeds 999.99 km. On the three raised dots on the face of the computer. *1 With the computer installed on the bracket, press Indicates whether the current speed is faster ( * The specifications and design are subject to change without notice. 1-53/64” x 1-7/32” x 5/8” (46.5 x 31 x 16 mm) / 0.78 oz (22 g) * The factory-loaded battery life might be shorter than the above-mentioned specification. Slow response or black LCD at lower or higher temperature may happen respectively.)ĭimensions/weight. ☏ - 104 ☏ (0 ☌ - 40 ☌) (This product will not display appropriately when exceeding the 0100 mm - 3999 mm (Default figure A: 2096 mm, B: 2096 mm) Working temperature. No contact magnetic sensor Wheel circumference range. 4-bite, 1-chip microcomputer (Crystal controlled oscillator) Display. ☌ temperature and the distance between the computer and theĬontroller. * This is the average figure of being used under 20 : Unit Total Distance reaches about 10,000 km (6,250 mile) 1 years (If the computer is used for 1 hour/day the battery life will vary Computer : Lithium battery (CR2032) x 1īattery life. Reinitialize the computer referring to “Preparing the computer”.īattery. Then reinitialize the computer referring to “Preparing the computer”. Is battery in the computer run down? Replace it. In the case of the computer, after replacing the battery, re-start the computer according to the “Preparing the computer”, above. Is the computer or sensor battery weak? In winter, battery performance diminishes. Are the computer and sensor too far apart? (The distance must not exceed 70 cm.) Install the sensor closer to the computer. Is the computer installed at the correct angle? Back of computer must face toward the sensor. Is the clearance between the sensor and magnet too great? (must beĭoes the magnet pass through the sensor zone? Adjust the positions of the magnet and sensor. If the icon now flashes, this indicates that the computer and sensor are too far apart or that the battery is low.) (The speed is not displayed.) (Spin the front wheel, bringing the computer closer to the sensor. The sensor signal reception icon does not flash. ![]() Wash off the bracket with water to get rid of any dirt, and to ensure that the computer slides in and out smoothly. 2825 Wilderness Place Suite 1200, Boulder CO80301-5494 USA Phone :Į-mail does not work when the computer is mounted on its bracket.Ĭheck that there is no dirt between the bracket and the computer. This does not affect your statutory rights.Ģ-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan Attn: For UK and REPUBLIC OF IRELAND consumers, please return to the place of purchase. Insurance, handling and transportation charges to CatEye shall be borne by person desiring service. Please write or type your name and address clearly on the warranty certificate. To return the product, pack it carefully and enclose the warranty certificate (proof or purchase) with instruction for repair. Service must be performed by CatEye or an authorized retailer. If the product fails to work due to normal use, CatEye will repair or replace the defect at no charge. After replacement, check the positions of the sensor and magnet.Ģ-Year Computer only (Accessories/Bracket sensor and Battery Consumption excluded) CatEye cycle computers are warranted to be free of defects from materials and workmanship for a period of two years from original purchase. Sensor If sensor reception is poor, replace the battery. * When the battery is installed, place the inner seal Install a new lithium battery (CR2032) with the (+) side facing upward. To clean the computer or accessories, use diluted neutral detergent on a soft cloth, and wipe it off with a dry cloth.Ĭomputer If the display appears faded, replace the battery. Pressing MODE increases the value, and pressing and holding MODE moves to the next digit. Reading will later allow you to enter the total distance manually. ![]() Before reinitializing the computer, note the total distance. To set the clock, refer to “Preparing the computer-4”. Pressing MODE increases the value, and pressing and Use this function if the computer is to be shared Toggle between the specified wheel size (tire circumference) ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |